New Posts New Posts RSS Feed - Would a grooved receiver support a SS?
  FAQ FAQ  Forum Search   Events   Register Register  Login Login

Check GunBroker.com for SWFA's No Reserve and No Minimum bid firearm auctions.

Would a grooved receiver support a SS?

 Post Reply Post Reply   Topic Search Topic Search  Topic Options Topic Options
Post Options Post Options   Thanks (0) Thanks(0)     Back to Top Direct Link To This Post Posted: June/16/2007 at 16:44
ba_50 View Drop Down
Optics Apprentice
Optics Apprentice


Joined: December/02/2004
Location: Illinois
Status: Offline
Points: 150
I've got a CZ 452 with grooved dovetail. Would it support the wieght of a Super Sniper? Thanks. Bob
Post Options Post Options   Thanks (0) Thanks(0)     Back to Top Direct Link To This Post Posted: June/20/2007 at 08:36
Urimaginaryfrnd View Drop Down
MODERATOR
MODERATOR
Avatar
Resident Redneck

Joined: June/20/2005
Location: Iowa
Status: Offline
Points: 13873
http://www.cz452.com/  site has some adaptors to go to Weaver then get some Weaver 30mm rings or similar rings and mount it.  While it may not be as rugged as having the reciever drilled and tapped by a gunsmith it should work for a .22 rifle.
Post Options Post Options   Thanks (0) Thanks(0)     Back to Top Direct Link To This Post Posted: June/20/2007 at 12:37
ba_50 View Drop Down
Optics Apprentice
Optics Apprentice


Joined: December/02/2004
Location: Illinois
Status: Offline
Points: 150

Uri,

 

I went to the site and looked at them, again. I thought one screw went in from the side but I was wrong. Someone had a good idea. I wonder if they will leave marks on the receiver. It might cost about the same to have it drilled and tapped. They used to charge $4 a hole but that has been awhile ago.

Post Options Post Options   Thanks (0) Thanks(0)     Back to Top Direct Link To This Post Posted: June/22/2007 at 09:05
Urimaginaryfrnd View Drop Down
MODERATOR
MODERATOR
Avatar
Resident Redneck

Joined: June/20/2005
Location: Iowa
Status: Offline
Points: 13873
Well drilling and tapping it would be the best route but it is always challenging to find a good gunsmith.
Post Options Post Options   Thanks (0) Thanks(0)     Back to Top Direct Link To This Post Posted: June/22/2007 at 09:21
Duce View Drop Down
Optics Master
Optics Master
Avatar

Joined: September/19/2006
Location: United States
Status: Offline
Points: 1231

I agree with Urimaginaryfrnd and you need a excelent gunsmith, a little out of alignment on the barrel is a long way out at 200 yards.

 

Duce 

Post Options Post Options   Thanks (0) Thanks(0)     Back to Top Direct Link To This Post Posted: June/22/2007 at 11:32
ba_50 View Drop Down
Optics Apprentice
Optics Apprentice


Joined: December/02/2004
Location: Illinois
Status: Offline
Points: 150
Yeh I know what you mean. I've had mostly bad experiences. A friend knows one who he considers to be excellent and reasonable. (If he will do it). He doesn't have to advertise nor does he want too.
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Similar Threads: "Would a grooved receiver support a SS?"
Subject Author Forum Replies Last Post
10mm rings for grooved .22 receivers made ba_50 Rimfire / Airgun 1 10/23/2006 7:15:55 PM
308 lower receiver trojan73 Firearms 18
30 mm rings that fit a 3/8 dovetail receiver mlv2k5 Rings and bases 4
Savage Receivers And Bases... The Apostle Rings and bases 14
I need your support for my master's thesis HunterFrank General Hunting 6
Ior Valdada customer support contact? castlebravo Rifle Scopes 13
-1 Leupold Customer Support MadMax Rings and bases 2
support for viewing with 15X binoculars Lurchernz Binoculars 2
European Uber Scope Customer Support? Brazos_Jack Rifle Scopes 13
National Match Rifle Support cheaptrick Firearms 0 1/29/2007 4:15:55 PM


This page was generated in 0.250 seconds.