Visit the SWFA.com site to check out our current specials. |
Leupold TMR reticle? |
Post Reply |
Author | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Kray
Optics GrassHopper Joined: January/08/2006 Location: United States Status: Offline Points: 39 |
Post Options
Thanks(0)
Posted: February/28/2009 at 14:31 |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
OK. So I kind of gave up on the idea of mounting a scope on my carry handle and decided to re-build with a flattop receiver. I was looking at the Leupold MR/T with the TMR reticle and noticedit had holdover marks for a 5.56 77 grn SPR round.
My problem is I can't seem to make the ballistics work. When I try to cross reference the data, it seems to be off by quite a bit. I was using a ballistics calculator and assuming a 77 grn BTHP bullet with a B/C of .372 running out at 2750 fps.
I wonder why the TMR holdover doesn't compute with my calcs? Am I using the wrong specs for the round? What is the assumed zero range for the TMR to come up with the holdovers marked?
Anybody else utilize this TMR with 77 gr rounds and find the hold overs correct?
Could I possibly ask more questions?
Kevin
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Urimaginaryfrnd
MODERATOR Resident Redneck Joined: June/20/2005 Location: Iowa Status: Offline Points: 14964 |
Post Options
Thanks(0)
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Now you've opened a can of worms. Different barrel length change the velocity. Different ammo changes the velocity and trajectory. For BDC knobs to be accurate you have to calculate them for the ammo you will be using as well as elevation and temperature. http://www.kentonindustries.com/
Kenton Ind will engrave knobs to your specs. problem solved.
As far as the reticle goes if you are using the marks for holdover go to the range shoot three shots at the same target at 200, 300, 400, 500, 600 all holding the center cross hair on the center of the target. Take a can of spray paint and mark where the holes are on the paper then go back to those distances and write down which line on the TMR corresponds to what distance at each range. Note like all BDC it only works if the power of the scope remains constant usually done at the highest power. But you can have a table for the highest power and a table for the lowest power made up very rapidly. Edited by Urimaginaryfrnd - March/02/2009 at 18:48 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
"Always do the right thing, just because it is the right thing to do". Bobby Paul Doherty Texas Ranger |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
supertool73
Optics God Superstool Joined: January/03/2008 Status: Offline Points: 11814 |
Post Options
Thanks(0)
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
That reticle is just a mil based reticle. It is not calibrated for a single load. You need to create a load and then figure out what your drops are and then u can use the mil marks to shoot for distance. http://www2.leupold.com/products/reticles_SPR.htm That is why you cannot get your data to fit it.
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Lifetime warranty and excellent customer service don't mean a thing when your gun fails during a zombie attack.
"A Liberal is a person who will give away everything they don't own." |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Dale Clifford
Optics Jedi Knight Joined: July/04/2004 Location: United States Status: Offline Points: 5087 |
Post Options
Thanks(0)
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
the mk 262 spr load will need about a mil at 200m but its velocities are closer to 2650, around 2mil at 300 and 3 mil at 400 m. which makes it a load calibrated to a reticle. (mildot). the set up works well and here is drop chart showing the drop in mils.
|