Visit the SWFA.com site to check out our current specials. |
Sensitive barrel? |
Post Reply | Page 12> |
Author | |
8shots
Optics Jedi Knight Lord Of The Flies Joined: March/14/2007 Location: South Africa Status: Offline Points: 6253 |
Post Options
Thanks(0)
Posted: September/14/2007 at 07:43 |
I had a new barrel fitted to a Sako 300H&H. The barrel is 24" 1in 10 twist. I have started tuning the loads to match the barrel (which is pillar bedded, free floated by a proffesional stock maker). I firstly found that new brass has to be fully resized before it fits in the chamber. Brass fired previously through a different rifle also has to be fully resized. Brass once fired through the new barrel only needs to be necksized and fits perfectly. Using the exact same load specs, except that the brass has either been fully resized or fire formed and necksized, I found that the results are very different. Fully resized not fired before brass = 4 inches and worse grouping. Once fired brass and neck sized only = 1and a half inch grouping. What is going on here? Is the chamber just reamed to very tight specs. Other then the issue with fire forming the brass first, everything else seems OK. Any comments??
|
|
RONK
Optics Master Extraordinaire Joined: April/05/2007 Location: United States Status: Offline Points: 3199 |
Post Options
Thanks(0)
|
Are you using two different sizing dies; one full length and one specialized neck-sizer? If so, it could be a bad full-length die. Neck-sizing usually gives better accuracy, but there shouldn't be that big a group by full-length sizing only, since your barrel shoots quite well otherwise. Just for kicks, slide a cardboard shim under the barrel at the fore-end tip to put some upward pressure on it and shoot a few with your best ammo. Post results. |
|
8shots
Optics Jedi Knight Lord Of The Flies Joined: March/14/2007 Location: South Africa Status: Offline Points: 6253 |
Post Options
Thanks(0)
|
I am using two different dies. Both dies worked well with previous barrel, so I doubt if it is the dies playing a role. A gunsmith friend of mine has an extremely accurate 308 custom rifle. I have seen him put 5 touching. He tells me that he has to fireform all of his shells. He in fact makes cheap lead bullets with a low powder load to blow the cases to fit the chamber. So I am curious to know if this is "normal" for rifles with tight chambers or is something else at play, like maybe a crooked neck ream?? The brass coming out of the new barrel looks straight and nothing obvious can be seen. The experience with the poor grouping of not previuosly fired brass is consistant over a number of firings. The rifle also is very sensitive regarding OAL and amount of powder. Groupings go way out when any one factor is only slightly changed. Edited by 8shots |
|
Dale Clifford
Optics Jedi Knight Joined: July/04/2004 Location: United States Status: Offline Points: 5087 |
Post Options
Thanks(0)
|
the chamber is a very "loose" chamber. when full length resizing the brass is being moved to min. dimension, and on firing the firing pin is pushing the case forward until the shoulder or bullet is touching depending on the OAL dimension, (a 300 HH with min. shoulder I'm quess its the bullet and why your showing such a range with OAL). on firing the case is sealing and pushing the web area back, but not as much as seen as a sharp shoulder. This was a common problem when the almost straight case HH was in its top of popularity, and one of reasons for the 300 win mag. If yur using the gun for target the camming action of the bolt should be used as much as possible in building neck sized fire formed cases that are difficult to close the bolt. a five shot, neck sized, very very tight case, chamber fit case. (pulled last rd) |
|
8shots
Optics Jedi Knight Lord Of The Flies Joined: March/14/2007 Location: South Africa Status: Offline Points: 6253 |
Post Options
Thanks(0)
|
Thanks for explanation Dale. I have tried to make this hunting rifle a target rifle. The only thing in which I succeeded was to drive my wife up the wall. I went the route of re-barreling and tuning this or that and never being satisfied. No more. This is a hunting rifle and I am happy to get 1inch groupings. I am also OK with it if I have to fire form all my brass. For target shooting I have ordered a Rem700 VSF in a 308.
Great shooting above Dale! Is that rifle for sale!!! |
|
RONK
Optics Master Extraordinaire Joined: April/05/2007 Location: United States Status: Offline Points: 3199 |
Post Options
Thanks(0)
|
For a rather slender barrel such as you have, !-1/2 inch groups are nothing to sneeze at anyway; plenty accurate for most hunting. That is great shooting Dale Clifford .
8-shots, I don't think Dale shot that group with a 300 H&H. If you look closely, it is noted 140 SMK at the top. To my knowledge, Sierra does not make a .30 Match King in that weight. Could be wrong tho'...Correct me here Dale? I'm also going to venture that it was fired from a rifle with a somewhat heavier barrel contour than the Sako you posted above. Just don't see too many pencil-barrelled belted magnums that put them all into the same hole. |
|
pyro6999
Optics Retard OT TITAN Joined: December/22/2006 Location: North Dakota Status: Offline Points: 22034 |
Post Options
Thanks(0)
|
looks like 190 or 192 or 195 smk to me
|
|
They call me "Boots"
375H&H Mag: Yeah, it kills stuff "extra dead" 343 we will never forget God Bless Chris Ledoux "good ride cowboy" |
|
pyro6999
Optics Retard OT TITAN Joined: December/22/2006 Location: North Dakota Status: Offline Points: 22034 |
Post Options
Thanks(0)
|
heres a 30 cal i shoot
|
|
They call me "Boots"
375H&H Mag: Yeah, it kills stuff "extra dead" 343 we will never forget God Bless Chris Ledoux "good ride cowboy" |
|
hot30
Optics Journeyman Joined: December/27/2006 Status: Offline Points: 378 |
Post Options
Thanks(0)
|
8shots, look at the case wall thikness of your new brass compared to that of your old brass. could the new stuff be "thicker" at the neck.?? might be some pinching going on if its thicker. your full length die will size allittle different on thicker brass( the neck expander)....... Your neck sizer is without the expander..??????????
Anyway, I would say your doing quite well, what do you want a CANNON to do about accuracy.. Hollow point boat tails.!!!!!!!!!!!!!!!!! Edited by hot30 |
|
30
|
|
RONK
Optics Master Extraordinaire Joined: April/05/2007 Location: United States Status: Offline Points: 3199 |
Post Options
Thanks(0)
|
Dale's target picture? Top left target? Penciled in? You read something other than 140 gr. SMK? O.K., I better get my eyes checked... Edited by RONK |
|
Dale Clifford
Optics Jedi Knight Joined: July/04/2004 Location: United States Status: Offline Points: 5087 |
Post Options
Thanks(0)
|
6.5x284 cooper 140 gr SMK. 2900 fps, just used to illustrate when neck sizing really pays off. its part of the erosion test started last spring. The 300HH biggest advantage is it's ability to feed and chamber even under the worst of conditions. 8shots--you didn't pick a cartridge that is the easiest to work with in a target sense. You will find the 308 more forgiving and without the strange happenings.
|
|
pyro6999
Optics Retard OT TITAN Joined: December/22/2006 Location: North Dakota Status: Offline Points: 22034 |
Post Options
Thanks(0)
|
sorry the image quality on my end looks very fuzzy. this computer i have is 7 yrs old
Edited by pyro6999 |
|
They call me "Boots"
375H&H Mag: Yeah, it kills stuff "extra dead" 343 we will never forget God Bless Chris Ledoux "good ride cowboy" |
|
RONK
Optics Master Extraordinaire Joined: April/05/2007 Location: United States Status: Offline Points: 3199 |
Post Options
Thanks(0)
|
Yeah that all makes sense. For serious target work 8shots also needs a heavier barrel, hence my suggestion to shim the forend to try and tighten the groups a bit more. Or possibly a lot more with a bit of luck. Really nice (and nice-looking) hunting rig regardless. |
|
8shots
Optics Jedi Knight Lord Of The Flies Joined: March/14/2007 Location: South Africa Status: Offline Points: 6253 |
Post Options
Thanks(0)
|
Thanks for all the feedback. You are all correct in that this rifle will not be a target rifle. I have given up on that quest and ordered a Rem700VSL in a 308 cal. I was however just trying to understand the "strange" behaviour for case preference. However, just to prove it can be done, I participated in a shooting competition this week-end. Distances from 200m, 100m and 50m. I ended up second out of 86 contestants, using the 300H&H! Walked away with a few nice prizes. |
|
Dale Clifford
Optics Jedi Knight Joined: July/04/2004 Location: United States Status: Offline Points: 5087 |
Post Options
Thanks(0)
|
congrats!!!
|
|
RONK
Optics Master Extraordinaire Joined: April/05/2007 Location: United States Status: Offline Points: 3199 |
Post Options
Thanks(0)
|
Good for you! That's gotta be pretty satisfying!
|
|
303Guy
Optics Apprentice Joined: September/02/2007 Location: New Zealand Status: Offline Points: 55 |
Post Options
Thanks(0)
|
8shots, is that S385 a ball or extruded powder? I had difficulty with Somchem ball powders when loading for 223 and 303. I abandoned it for the older MR200 (pretty good stuff), for both 223 and 303. My 223 shot 3 MOA with factory ammo and 1 1/4 MOA with reloads, getting down to 3/4 MOA with match bullets. Have you considered heavier bullets? My understanding is that the 300H&H was designed for heavies.
Congrats on your shooting!
Edited by 303Guy |
|
Regards
303Guy |
|
8shots
Optics Jedi Knight Lord Of The Flies Joined: March/14/2007 Location: South Africa Status: Offline Points: 6253 |
Post Options
Thanks(0)
|
Thanks for all the nice remarks. I do feel vindicated, as I drove my wife nuts in the process of getting the rifle sorted out. At least I came home with the meat! Literally, as part of the prize was 2kg of beef fillet! 303Guy, the S385 is extruded. For target shooting I think the 178gr is about perfect as it gives a relatively flat trajectory and can still buck the wind. For hunting I use the 200gr Nosler Part, which is enough to knock down anything I hunt. However, the heavier bullets are more difficult to stabilize. I struggled a fair amount last time round to get the right powder combo and seating depth. |
|
Dale Clifford
Optics Jedi Knight Joined: July/04/2004 Location: United States Status: Offline Points: 5087 |
Post Options
Thanks(0)
|
don't know if this has been covered before (to lazy to read back) but 200+ gr 308 need 11 or faster twist rate.
|
|
303Guy
Optics Apprentice Joined: September/02/2007 Location: New Zealand Status: Offline Points: 55 |
Post Options
Thanks(0)
|
Dale, 8shots did say his twist is 1 in 10. I know little about the 300 H&H but I did have the impression that it is a good shooter so I am quite intrigued that there is a difficulty. I am reloading for a vaguely similar geometry case - the hornet - with a huge bullet jump and thought I would have accuracy problems with mag fed loads but found it to be quite forgiving and have found a way of making the bullets enter the rifling nice and straight. Nothing to do with the 300. |
|
Regards
303Guy |
|
Post Reply | Page 12> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |