Visit the SWFA.com site to check out our current specials. |
After years, I figured out why bases get loose |
Post Reply |
Author | |
Clark
Optics Apprentice Joined: February/13/2004 Location: Near Seattle Status: Offline Points: 124 |
Post Options
Thanks(0)
Posted: August/21/2015 at 22:10 |
I have hundreds of rifles and when I take another beater rifle I just rebarrelled to the range, half the time I get lousy groups, it is loose scope bases.
I take tools to the range and help other shooters, and half the time they get bad groups, it is loose bases. Typically two Weaver scope bases and each base has two 6-48 screws. Grade 5 bolts are good for 127 ksi in tension 6-48 screws have a 0.12" root [minor diameter] Area = pi r squared = 3.140(0.120/2)^2 = 0.0112 sq in Tension = area time stress = .0113 sq in 127 kpsi = 1456 pounds tension per screw There are 4 screws = 5745 pounds potential clamping force. The screws are only loaded up typically to 50% of rating = 2873 pounds clamping. If I look in quickload at the 6.5-06 I just built with a 142 gr Nos Bal tip Long range bullet accelerates from 500 fps to 2000 fps in 0.4 ms. An 8 pound rifle in recoil reaction would then accelerate in proportion from 1.27 fps to 5.07 fps in 0.4ms This is a peak acceleration of 9500 ft/sec sec If a 2 pound scope were attached to a 6 pound barrelled action and stock they would act as an 8 pound single mass. The mass of the 2 pound scope is = [weight]/[gravity] =[2]/[32 f/ss] = 0.0625 slugs Force = mass acceleration = [.0625 slugs ][ 9500 ft/sec sec]= 594 pounds of force pushing back on the scope in recoil The Mausers I just built is made of steel, as are the modified S54 and S46 bases. Looking up the coefficient of static friction of steel on steel: https://en.wikipedia.org/wiki/Friction is 0.74 ~ 0.80 for dry and clean steel Averaging the two would be 0.77 The static friction force threshold of slipping = [coefficient of friction clean steel][clamping force] = [.77][2873 pounds= 2212 pounds. Because the static friction 2212 pounds is greater than recoil reaction on the scope mass 594 pounds, the scope should not slip. But the coefficient of friction for lubricated steel on steel is 0.16 The static friction force threshold of slipping = [coefficient of friction lubricated steel][clamping force] = [.16][2873 pounds= 459 pounds. Because the static friction 459 pounds is less than the recoil reaction on the scope mass 594 pounds, the scope should slip and the screws should start shaking loose. |
|
urbaneruralite
Optics Journeyman Joined: January/03/2008 Status: Offline Points: 479 |
Post Options
Thanks(0)
|
Someone ought to write a textbook called Practical Physics for the American Male. It should teach following a model of examples as above to show how the seemingly abstract concepts apply to things young fellas might actually care about.
I bet it would sell to the home school crowd. I'd sure buy it! |
|
Steelbenz
Optics Jedi Knight ROLL TIDE ROLL Joined: January/03/2006 Location: Heart of Dixie Status: Offline Points: 5153 |
Post Options
Thanks(0)
|
Bed your bases and use blue loctite.
|
|
"Don't argue with a fool! From a distance you can't really tell who's who!"
|
|
Rancid Coolaid
MODERATOR Joined: January/19/2005 Location: United States Status: Offline Points: 9318 |
Post Options
Thanks(0)
|
That all looks very complicated, and I am a dumb ol' Marine.
I can say this: I have fired hundreds of rifles, many thousands of rounds, and have had almost no problems whatsoever with scope bases moving or coming loose. I have mounted hundreds of scopes, have had some rings-to-bases shoot loose, some ring halves loosen, almost no bases loosen. The exception to this was a few Tikka's with terrible stock rings. And one 300WM that was shooting 190-gr rounds at about 2900 FPS from a 7-pound gun, it had a brake, which means it was getting the double-whammy on recoil, it had a base that needed adjusting. Once. My experience has ranged from 22LR up to 50-cal, I just don't have issues with bases shooting loose. I am a bit concerned that you are mounting barrels but not checking torque on the bases prior to going out for test firing. Of hundreds of rifles, "half the time" you get lousy groups due to bases: if that statement is even partially accurate, you are doing something very, very wrong. Are you familiar with loctite (more info http://www.loctiteproducts.com/)? Are you using quality bases? You mention weaver, but I don't know if that is the style or the brand, this could be part of the problem. On the physics, college physics was a long time ago for me, but I seem to recall that screws make the calculations a bit more complicated, and an adhesive makes it even more difficult. I applaud your efforts at analyzing the problem, but just don't see the problem in the same light. You are re-barreling actions, regularly, and having difficulty with scope bases? I am not understanding some part of this conversation.
|
|
Freedom is something you take.
Respect is something you earn. Equality is something you whine about not being given. |
|
338LAPUASLAP
Optics Master Scope Swapper Joined: October/17/2009 Status: Offline Points: 2596 |
Post Options
Thanks(0)
|
Agree.
Many new base combos use loctite now suprisingly I have not used the supplied loctite and have put a few down the barrel without getting loose screws. Some I even use neverseeze or a similar product due to the fact I do lots of swapping... Properly torqued even with the heavy hitters on SLR or autos and no issues. Follow the base and rings or base/ring manufacturer instructions. Use the proper amount of torque, get the wheeler or the borka and do not guess. Dis regard the very first post because if you follow the correct procedure you will not have loose screws on your rifle like the loose screw up top, and all the mechanical enegineering and all applied physics in the world don't matter a hill o beans if you cant follow directions. |
|
Son of Ed
Chuck Norris Joined: June/18/2011 Location: TEXAS Status: Online Points: 122186 |
Post Options
Thanks(0)
|
|
|
Visit the Ed Show
|
|
Sparky
Optics Master Extraordinaire Joined: July/15/2007 Location: SD Status: Offline Points: 4569 |
Post Options
Thanks(0)
|
Are you using a torque wrench to tighten your bases and rings?
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |