Visit the SWFA.com site to check out our current specials. |
Need help. Why is this happening? |
Post Reply | Page 12> |
Author | |
JimFromTN
Optics Apprentice Joined: February/05/2010 Location: United States Status: Offline Points: 191 |
Post Options
Thanks(0)
Posted: February/14/2015 at 13:05 |
This was a brand new un-fired piece of brass. The load was 2 grains less than the max recommended load according to Hogden. The load was 300 win Mag 200 gr Nosler Partition 70 gr H4831 Winchester large rifle magnum primer The bullet is seated .04 off of the lands. According to the Hogden Manual, the max load is 72 gr H4831 using a winchester large rifle magnum primer. According to Nosler the max load is 71.5 gr H4831 with a Fed 215 primer. The Nosler guide groups Accubonds and partitions together. The Hogden guide seperates them and says the max load for the accubond is 71.5 gr. I am wondering if I should back up from a magnum primer to a large rifle primer. This is making a mess of my bolt face. Edited by JimFromTN - February/14/2015 at 13:16 |
|
3_tens
Optics Jedi Master Joined: January/08/2007 Location: Oklahoma Status: Offline Points: 7853 |
Post Options
Thanks(0)
|
Did you start at 67 and work your way up or did you start at Max load. Not all rifles can handle max load because of variances in cambering. If you worked up to max, at what point did the primers start to blow out.
|
|
Folks ain't got a sense of humor no more. They don't laugh they just get sore.
Need to follow the rules. Just hard to determine which set of rules to follow Now the rules have changed again. |
|
JimFromTN
Optics Apprentice Joined: February/05/2010 Location: United States Status: Offline Points: 191 |
Post Options
Thanks(0)
|
They started to blow out at 68.5 grains which is 2 grains less than the max according to nosler and 2.5 grains below max according to Hogden.
|
|
3_tens
Optics Jedi Master Joined: January/08/2007 Location: Oklahoma Status: Offline Points: 7853 |
Post Options
Thanks(0)
|
There are so many variables. Did you do any prep to the primer pocket. Did you crony the velocity. Do you have a crony If not get one. The one thing for sure is that you do not want to shoot any more of these shells. Take any remaining, break them down and verify that each component is what it was supposed to be. Test your scale to verify its accuracy. Verify your powder. I know a man that stopped in the middle of a session and when he came back and changed his powder mistakenly pored it into a different container. The mix was not healthy. When you suspect a problem stop and start over. Label everything you do. If you put powder in the dispenser, Put a label on it. Bullets in a tray Label it. Keep a log and record all your weights and measurements. The key to successful reloading is to be meticulous.
|
|
Folks ain't got a sense of humor no more. They don't laugh they just get sore.
Need to follow the rules. Just hard to determine which set of rules to follow Now the rules have changed again. |
|
JimFromTN
Optics Apprentice Joined: February/05/2010 Location: United States Status: Offline Points: 191 |
Post Options
Thanks(0)
|
I don't have a chrony but it was brand new brass and I bought the powder a couple of weeks ago so nothing is miss labelled. I weighed the bullets to make sure they were not mislabelled from nosler and they weighed ok so I think my scale is ok.
I hate to do it but I may go buy some factory ammo and make sure it does not happen with the commercial stuff. If it does then its not the load and I need to look at the rifle.
|
|
Rancid Coolaid
MODERATOR Joined: January/19/2005 Location: United States Status: Offline Points: 9318 |
Post Options
Thanks(0)
|
Can you take a better picture of the brass? I think there are clues that cannot be resolved in that picture. A better picture will help.
In the end, it could be brass or recipe or rifle - or some combination. |
|
Freedom is something you take.
Respect is something you earn. Equality is something you whine about not being given. |
|
Rancid Coolaid
MODERATOR Joined: January/19/2005 Location: United States Status: Offline Points: 9318 |
Post Options
Thanks(0)
|
For clarity: brand new rifle, brand new brass, brand new components?
|
|
Freedom is something you take.
Respect is something you earn. Equality is something you whine about not being given. |
|
JimFromTN
Optics Apprentice Joined: February/05/2010 Location: United States Status: Offline Points: 191 |
Post Options
Thanks(0)
|
Brand new brass and components. Rifle has somewhere around 1000 rds thru the barrel.
|
|
3_tens
Optics Jedi Master Joined: January/08/2007 Location: Oklahoma Status: Offline Points: 7853 |
Post Options
Thanks(0)
|
What brand of brass? I have read where some have complained about bad batches coming out of Remington recently.
|
|
Folks ain't got a sense of humor no more. They don't laugh they just get sore.
Need to follow the rules. Just hard to determine which set of rules to follow Now the rules have changed again. |
|
JimFromTN
Optics Apprentice Joined: February/05/2010 Location: United States Status: Offline Points: 191 |
Post Options
Thanks(0)
|
Both Privi partison and remington have had the issue.
I went to the range today and bought some remington corelokts. I also brought some target loads which I have shot hundreds of in the past with no issues. I shot every coreloct without a single issue. I shot 5 of the target loads and the 5th one blew the primer. There were 2 commonalities between the target loads and the hunting loads. The first was the primer (winchester large rifle magnum primers)and the 2nd was the temperature. I have been to the range 3 times now where the primers blew and all 3 times the temperature was in the 20's. Could the temperature be causing a spike in pressure when using the winchester primers? I bought some CCI 250's which I will try next.
|
|
pyro6999
Optics Retard OT TITAN Joined: December/22/2006 Location: North Dakota Status: Offline Points: 22034 |
Post Options
Thanks(0)
|
according to the online data on noslers webpage 70.5gr of h-4831 is max.... I would strongly suggest you dont go to a standard larger rifle primer either. Does the rifle's bolt require extra effort to close before firing??
I have been shooting magnums most of my life in temps colder than 20 degrees and ive never had a magnum of any caliber do that to a case head. I have seen that in the .22-250 a few times when the loads were a bit to warm. Im gonna go ahead and guess that you will be seeing this same result no matter which primer you try. Im thinking you may want to back off the loads and maybe even consider changing the depth you seat your bullets to. |
|
They call me "Boots"
375H&H Mag: Yeah, it kills stuff "extra dead" 343 we will never forget God Bless Chris Ledoux "good ride cowboy" |
|
DCAMM94
Optics Master Extraordinaire Joined: April/19/2008 Location: Fort Worth Status: Offline Points: 3491 |
Post Options
Thanks(0)
|
[QUOTE=pyro6999]Im thinking you may want to...consider changing the depth you seat your bullets to.
[/QUOTE That was my first thought as well. |
|
Although personally I am quite content with existing explosives, I feel we must not stand in the path of improvement. -Winston Churchill
|
|
JimFromTN
Optics Apprentice Joined: February/05/2010 Location: United States Status: Offline Points: 191 |
Post Options
Thanks(0)
|
Hogden seperates accubonds from partitions where as nosler groups them together. |
|
DCAMM94
Optics Master Extraordinaire Joined: April/19/2008 Location: Fort Worth Status: Offline Points: 3491 |
Post Options
Thanks(0)
|
Have you measured how far your factory loads are seated off the lands?
|
|
Although personally I am quite content with existing explosives, I feel we must not stand in the path of improvement. -Winston Churchill
|
|
JimFromTN
Optics Apprentice Joined: February/05/2010 Location: United States Status: Offline Points: 191 |
Post Options
Thanks(0)
|
Unfortunately, I shot up the entire box and did not measure them. I assume they were spec where the OACL was 3.340. The target loads that I loaded are 3.489. Like I said about the target loads, I have shot over 200, probably closer to 300, of these without a single issue. The hunting loads are 3.58 which is .046 off of the lands.
|
|
V98
Optics GrassHopper Joined: December/09/2011 Status: Offline Points: 17 |
Post Options
Thanks(0)
|
If the primer failed at the cup radius as it looks like in the pic, then this has been an intermittent issue with WLR and WLRM's for the past few years or so.There are a few threads at the CMP forums concerning this issue.Contact Winchester and ask them to take back your remaining primers and pay for a new bolt for your rlfle.
|
|
JimFromTN
Optics Apprentice Joined: February/05/2010 Location: United States Status: Offline Points: 191 |
Post Options
Thanks(0)
|
I believe you are right. I looked at the pictures of the primers that people are posting and they look the same.
|
|
Alan Robertson
Optics Master Joined: October/31/2009 Location: Oklahoma Status: Offline Points: 1763 |
Post Options
Thanks(0)
|
in re Winchester primers: Thanks for the heads up.
I've not had any issues with WLR or M primers, but haven't loaded anything "hot" with them since buying an available large stock and now have too large a stock to not use them up. Count on them only being used for low pressure apps. All my Win pistol primers of all flavors have never been a problem, but they are all far from rifle pressure. >>>I've quit using Win small rifle primers at all, as I had pierced primers with AR loads between SAAMI and Nato spec pressure, at what I figured would be around 55- 56K psi. No other pressure signs were evident and I've found that there is a lot of talk on the net about this issue, which is caused by too thin/soft primer cups. I never had an issue with their old nickel plated primers in any rifle. From what others have told me, Winchester is aware of their primer problems and have quietly been fixing guns damaged by their primer issues, without publicly making statements (or changing their cups, so far.) I've not had any issues at all with any flavor CCI small rifle primer or Federal 205 or 205Ms. |
|
"Garg'n uair dhuisgear"
|
|
pyro6999
Optics Retard OT TITAN Joined: December/22/2006 Location: North Dakota Status: Offline Points: 22034 |
Post Options
Thanks(0)
|
rl-22 is not h4831, so making any comparison is a moot point, they each will act different. My point was that this is a pressure related issue, and for your safety i recommended backing off until the problem was pinpointed.... If there is a known issue with winchester's primers then i would probably stop using them. here is the data straight from noslers webpage which they grouped the partition and the accubond together.... http://static1.squarespace.com/static/5163436ce4b0b470bd1fbb00/t/51ba2b75e4b03a11938d4558/1371155317785/300-Win-Mag-200gr-Version+7.0.pdf |
|
They call me "Boots"
375H&H Mag: Yeah, it kills stuff "extra dead" 343 we will never forget God Bless Chris Ledoux "good ride cowboy" |
|
V98
Optics GrassHopper Joined: December/09/2011 Status: Offline Points: 17 |
Post Options
Thanks(0)
|
|
|
Post Reply | Page 12> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |