OpticsTalk by SWFA, Inc. Homepage SWFA     SampleList.com
Forum Home Forum Home > Scopes > Rifle Scopes
  New Posts New Posts RSS Feed - Zeiss Rapid Z-600
  FAQ FAQ  Forum Search   Events   Register Register  Login Login

Visit the SWFA.com site to check out our current specials.

Zeiss Rapid Z-600

 Post Reply Post Reply
Author
Message
Pokeshunter View Drop Down
Optics GrassHopper
Optics GrassHopper


Joined: August/27/2010
Status: Offline
Points: 2
Post Options Post Options   Thanks (0) Thanks(0)   Quote Pokeshunter Quote  Post ReplyReply Direct Link To This Post Topic: Zeiss Rapid Z-600
    Posted: August/27/2010 at 19:08
Was wondering how much the focus will mess with the ballistics on my Z-600 reticle. I was playing with the focus and when you move the focus adjustment out, the reticle becomes noticably larger so was wondering if the results from the calculator are for the focus adjustment being all the way in or out? Or if it will even make a difference?
Back to Top
Alan Robertson View Drop Down
Optics Master
Optics Master
Avatar

Joined: October/31/2009
Location: Oklahoma
Status: Offline
Points: 1763
Post Options Post Options   Thanks (0) Thanks(0)   Quote Alan Robertson Quote  Post ReplyReply Direct Link To This Post Posted: August/27/2010 at 21:57
Hello Pokeshunter and welcome to the forum. I know some old boys at OSU that might be curious about your moniker.
You aroused my curiosity so I had to check, but didn't find the reticle getting larger with my Z600.
My eyes have been around awhile and have seen a few things, so YMMV... ( I do wear glasses with Zeiss lenses.)

I cranked the focus range stop-to-stop a few times and measured the length and height of the center reticle against a tape measure placed across the room. I tried to maintain a normal eye relief to minimize extraneous input.. The scope was on 3x since either reticle or tape was too out of focus on higher powers to be able to make measurements. I had to try this with glasses on/off to be able to see the reticle and measurement points at each end of the dial. If there was a change/difference, it wasn't enough to see. Everything seemed to 'fit' the same whether at the extremes or while focused. Measurements weren't exact, but were nevertheless close, since something was always at least slightly out of focus. I tried this a bunch of times to make sure...

Zeiss would have the definitive answer, but the question is really moot as you won't be shooting except when focused for your eyes, anyway.

By the way, my Conquests have a very forgiving and wide focus range for me... I know where the diopter markings are optimally aligned on the ocular, but it's no biggie if they get moved while handling the rifles.



Edited by Alan Robertson - August/27/2010 at 21:59
"Garg'n uair dhuisgear"
Back to Top
sakomato View Drop Down
Optics Master
Optics Master
Avatar

Joined: February/28/2008
Location: Houston
Status: Offline
Points: 1166
Post Options Post Options   Thanks (0) Thanks(0)   Quote sakomato Quote  Post ReplyReply Direct Link To This Post Posted: August/27/2010 at 22:41
Your scope has 4 adjustments:
 
 
Turrets - elevation and windage turrets are used to adjust the point of impact of your bullet to align with the crosshairs
 
Parallax adjustment - it is the dial on the left side of the scope in line with the elevation turret and opposite the windage turret.  When looking through the scope at a distant object, adjusting the parallax adjustment will make the image clearer.  You may not have this if your scope is not high enough power for Zeiss to think you need one.  You did not tell us what power scope you had.
 
Power adjustment - it is the ring that goes around the scope on the front part of the ocular where you adjust the power from 3 to 9, 3.5 to 10 or 4.5 to 14, depending upon which scope you have.   You use the power adjustment to set your scope so that the long range reticles will be on for whatever caliber and load you are shooting.  You go to the Zeiss website and put your ballistics in the RapidZ Calculator and it will tell you what power to set your scope on so that your load will hit on your reticle marks.
 
Reticle focus - it is the ring on the ocular closest to your eye.  You point the scope at a blank wall and adjust the reticle focus adjustment until the reticle is clear and in a single line, not fuzzy.  You focus the reticle adjustment only once to make the reticle clear.
 
Now, what adjustment are you moving that makes your reticle larger?
 


Edited by sakomato - August/27/2010 at 22:46
Guns only have 2 enemies, rust and politicians
Back to Top
gunner45 View Drop Down
Optics GrassHopper
Optics GrassHopper
Avatar

Joined: August/20/2010
Location: Texas
Status: Offline
Points: 7
Post Options Post Options   Thanks (0) Thanks(0)   Quote gunner45 Quote  Post ReplyReply Direct Link To This Post Posted: August/28/2010 at 13:00
I was wondering that myself.
Back to Top
Jon A View Drop Down
Optics Journeyman
Optics Journeyman
Avatar

Joined: March/14/2008
Location: Everett, WA
Status: Offline
Points: 670
Post Options Post Options   Thanks (0) Thanks(0)   Quote Jon A Quote  Post ReplyReply Direct Link To This Post Posted: August/28/2010 at 15:03
Pokes,

I believe you were noticing the small change in magnification that happens when you play with the ocular focus.  Since this occurs at the aft end of the scope, the change it causes happens to both the reticle and the image together so there is no relative change between the two.  The subtension of the reticle will remain constant.

In other words, it will make no difference.
Back to Top
tjtjwdad View Drop Down
Optics Journeyman
Optics Journeyman


Joined: December/11/2007
Status: Offline
Points: 365
Post Options Post Options   Thanks (0) Thanks(0)   Quote tjtjwdad Quote  Post ReplyReply Direct Link To This Post Posted: August/30/2010 at 00:27
Jon A,
 
You're right.  I have three Conquest scopes (3.5-10x44, 4.5-14x50 and a 6.5-20x50) and they all do it.  I've alway figured it was a moot point because when its focused its a done deal.
 
Jim 
Back to Top
2Tonic View Drop Down
Optics GrassHopper
Optics GrassHopper
Avatar

Joined: June/14/2009
Location: NW Indiana
Status: Offline
Points: 22
Post Options Post Options   Thanks (0) Thanks(0)   Quote 2Tonic Quote  Post ReplyReply Direct Link To This Post Posted: August/30/2010 at 01:37
Jon A    Thunbs Up +1

Pokeshunter, using the results of the Rapid Z Calculator has my 3-9x40 Zeiss Conquest set at 6.75x for a 77gr MK262 load out of a 20", 1in8 RRA. If I do my part for windage it will drop rounds right on target at 600yds. My son gets the same results even though he changes the focus to suit his vision, so I really do believe it's nothing to fret about.

"Excreta tauri vincit omnia"
Back to Top
Pokeshunter View Drop Down
Optics GrassHopper
Optics GrassHopper


Joined: August/27/2010
Status: Offline
Points: 2
Post Options Post Options   Thanks (0) Thanks(0)   Quote Pokeshunter Quote  Post ReplyReply Direct Link To This Post Posted: September/01/2010 at 08:29
Its the reticle focus adjustment used, the scope and reticle are pretty much focused from the closest focus adjustment to it locked in the farthest away so was just wondering if there was a difference. My optimum power for the load I shoot is 7.96 but havent yet found the right bullet for the set up Im shooting. Thanks guys and sorry to dissapoint but I have never been to OK.
Back to Top
sakomato View Drop Down
Optics Master
Optics Master
Avatar

Joined: February/28/2008
Location: Houston
Status: Offline
Points: 1166
Post Options Post Options   Thanks (0) Thanks(0)   Quote sakomato Quote  Post ReplyReply Direct Link To This Post Posted: September/01/2010 at 19:50
Pokeshunter, you focus the reticle adjustment only once to where the reticle is a sharp clean clear black line without being fuzzy or having a smaller mirror reticle line.  If the reticle is out of focus it is like looking at a 3D image without the 3D glasses.
 
If you are using the reticle adjustment to make the image clearer then you will be making the reticle fuzzy and you don't want to do that.
 
What power scope?
What caliber rifle?
What bullet do you want to shoot?  i.e. hunting, target, bonded, Whitetail, Varmint, Elk etc.?
Guns only have 2 enemies, rust and politicians
Back to Top
cornhuskid View Drop Down
Optics Apprentice
Optics Apprentice


Joined: January/11/2010
Status: Offline
Points: 113
Post Options Post Options   Thanks (0) Thanks(0)   Quote cornhuskid Quote  Post ReplyReply Direct Link To This Post Posted: September/08/2010 at 09:52
I have not noticed any practical defference with my Conquest 3-9x40 when adjusting the "Reticle Adjustment" and point of impact, but I'm only going out to 550 yards with an '06...
 
 
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.01
Copyright ©2001-2018 Web Wiz Ltd.

This page was generated in 0.492 seconds.