Visit the SWFA.com site to check out our current specials. |
Scope base Lapping and Reaming |
Post Reply | Page 12> |
Author | |
saitotiktmdog
Optics Apprentice Joined: June/08/2010 Location: IN Status: Offline Points: 256 |
Post Options
Thanks(0)
Posted: August/17/2010 at 08:45 |
Not too long ago I came across an article by Larry Willis about the proper way to mount a scope. I had never seen the tools he was using and had never considered reaming my scope rings. My opinion on the matter is depending on the scope rings etc this may or may not be necessary. I have a set of scope rings that do not fit well on my scope. Instead of buying the 100 plus dollar scope reamer I am using a metal file with a rounded profile. I am taking my time and checking fitment with the scope frequently. In addition to the file I am using sand paper. Once I get it close I will mount the rings to the gun and check overall alignment. I am even considering enlarging the rings enough so that I could wrap the scope with say some blacke electrical tape where the rings go and then clamping over the tape as a reducer per say. I worked on them some last night and so far results are good. The rings originally would not allow the scope to drop all the way in adn would bind on the half corners.
Also I would like to get other opinions on reaming/lapping. I did some searching on here and could not find much about this topic so I thought I would start a thread. www.larrywillis.com/mountingascope.html
|
|
supertool73
Optics God Superstool Joined: January/03/2008 Status: Offline Points: 11814 |
Post Options
Thanks(0)
|
Sounds like a lot of work, when scope rings can be had for such good prices these days.
|
|
Lifetime warranty and excellent customer service don't mean a thing when your gun fails during a zombie attack.
"A Liberal is a person who will give away everything they don't own." |
|
3_tens
Optics Jedi Master Joined: January/08/2007 Location: Oklahoma Status: Offline Points: 7853 |
Post Options
Thanks(0)
|
I would never trust filing on a ring. Any imperfections will damage the tube and very likely destroy the scope. Of course when the scope gets messed up it will make good foder for KBs Lott. |
|
Folks ain't got a sense of humor no more. They don't laugh they just get sore.
Need to follow the rules. Just hard to determine which set of rules to follow Now the rules have changed again. |
|
saitotiktmdog
Optics Apprentice Joined: June/08/2010 Location: IN Status: Offline Points: 256 |
Post Options
Thanks(0)
|
|
|
stickbow46
Optics Master Extraordinaire Joined: January/07/2009 Location: Benton, Pa Status: Offline Points: 4678 |
Post Options
Thanks(0)
|
First off I Use an allignement tool to make sure the gun was taped in aligement with front & rear sight,then I proceed with the lapping tool & I clear about 85/90% of the high spots off.Usually it's about 40-50 strokes,using a #20 grit!
I've used all kinds of rings[Talley's Burris ,Loupey's,T/C]just about everything out there & including Rock River,AR15 & GGG to name a few.Point is'they all had high spots that had to be honed.
Why spend the big bucks on those well made rings & ass u me they are straight? The process takes all of 10 mins & can make a world of difference in the accuracy of a scope.
They cost about $40 for each size & if I can do it,it just about idot proof,just go slow ,consistant strokes & check about every 15 strokes on the amount of high spots removed.
Also remember to use a long lasting rust resistant oil on your rings when done,don't worry about the paint you have removed as no one can see the bottom bald spot.
|
|
Pearls of Wisdom are Heard not Spoken
|
|
supertool73
Optics God Superstool Joined: January/03/2008 Status: Offline Points: 11814 |
Post Options
Thanks(0)
|
Thing about lapping is the bar is long enough to engage both rings at the same time so they are done evenly. By doing each ring differently you will never get them the exact same. Which will cause them to be on slightly different planes. Then when you tighten down your scope since they are on different planes it will put a bind on your scope tube. Which can cause scope failure.
I know you think what you are going is going to help, but I assure you it is doing more damage than good. There is a reason the Kokopelli and WHeeler accuracy kits come with alignment bars. You need them to check and make sure the changes you are making on your rings is allowing them to stay in the same plane. In all honestly lapping a reaming is a thing of the past with good modern rings and bases. Good quality equipment is is machined to very good tollerances. If you bed your base properly )as it is typically the receiver that it out of whack on the rifle) then your rings with line up perfectly. If your rings would not let your scope fall into them, then they are either to small for the scope you have or they are bad rings. The imprefections he is talking about is not just little rough spots you might create, but possibly actually more than likely the out of round that you are making your rings. Which in turn when you tighten your scope down with possibly force your scope tube out of round also. And if you make them to large then your scope will slip during recoil. Proper good mounts are as important for accuracy as the rifle and scope are. Your scope needs to be fitted squarely, torqued properly, have full contact with all parts of the rings, and not slip to be working properly. Any of those problems can lead to accuracy problems or possible scope failure. You will be much better off just buying a new set of rings. |
|
Lifetime warranty and excellent customer service don't mean a thing when your gun fails during a zombie attack.
"A Liberal is a person who will give away everything they don't own." |
|
supertool73
Optics God Superstool Joined: January/03/2008 Status: Offline Points: 11814 |
Post Options
Thanks(0)
|
More than likely the high spots you think you are seeing is because the receiver of your gun is not square. I used to think just like you, thinking you need to lap away at those rings. Then I learned that most receivers are in fact out or square. So then you bed your base with devcon and make sure it is prefectly square. Then suddenly all those rings that seemed out of whack now align perfectly with each other. All those rings I lapped suddenly do not work anymore because I lapped angles in them. I have bedding several bases now and every time with the brand new quality rings I am buying they align perfectly. Don't be confused that it is the mounting hardware. Most cases they are going to be great if you buy quality parts. There is a good reason most ring companies void the warranty if you lap their rings. It ruins them and makes them larger than they should be. Fix the actual problem which is the receiver, don't try putting a bandaid on the mounting hardware. |
|
Lifetime warranty and excellent customer service don't mean a thing when your gun fails during a zombie attack.
"A Liberal is a person who will give away everything they don't own." |
|
saitotiktmdog
Optics Apprentice Joined: June/08/2010 Location: IN Status: Offline Points: 256 |
Post Options
Thanks(0)
|
The rings are 30mm rings and the scope is a 30mm scope so the rings are not too small for the scope. It is possible that the scope is out of round a bit but I just got it back from bushnell repaired so I think the scope will still work fine, especially on my 17hmr. Manufacturing tolerances vary between parts. When you have three separate entities (assuming you are not using rings with built in bases but it still applies there just not as much) it is likely that there will not be perfect alignment simply because the holes in you gun for the scope rail might be off a thousanth, as well as the hole in the rail, or whatever. Anyway the point is to get those three things to line up perfectly with no deviation is neary impossible. Just because you cant tell with the naked eye does not mean its not off. There will be some deviation. Just look at a bolted joint dva. There is an allowable amount of variance which is caled the manufacturing tolerances. Anyways not trying to get anybody riled up here. I still think I will proceed with what I am doing.
In addition there were plenty of quality parts made by hand back in the day using files and other hand finishing tools etc to get the best fit and finish during final assembly. Not to mention back in the day before factory machinery. Some very fine accurate guns have been made that have been filed on or who knows what else. Even today Many a time I have seen video in firearm assembly plants where someone is using file to make sure two parts fit together better. It just takes time and patience. Someone along the way just came up with the tools to make it faster and easier. IE scope lapping and reaming tools.
|
|
stickbow46
Optics Master Extraordinaire Joined: January/07/2009 Location: Benton, Pa Status: Offline Points: 4678 |
Post Options
Thanks(0)
|
I totally agree with you in that both rings must have the lapping bar touch them together,I use a Robert Hart 14" bar[same Bob Hart of barrel fame]He makes one of the best scope rings around & he recommends lapping his own rings.
His shop is only 12mls from where I live so any gun work I need riifle I need to have done that the place I go too.
I was a tool & die man for 6 years & I totaly agree with Lappinng to remove high points!FYI the only perfect flat suface was done by hand using prussian blue ink,3 flat steel surface plates & a triangular shaped file with no teeth on it!
I thank you for your feed back & very knowledgable input.I agree with some of your points,but I still remain firm in that no one makes the perfect fit rings,just my 2cents
|
|
Pearls of Wisdom are Heard not Spoken
|
|
saitotiktmdog
Optics Apprentice Joined: June/08/2010 Location: IN Status: Offline Points: 256 |
Post Options
Thanks(0)
|
I agree as well.
|
|
supertool73
Optics God Superstool Joined: January/03/2008 Status: Offline Points: 11814 |
Post Options
Thanks(0)
|
Here is some info from Glen Seekins on the subject. I have talked to him on the phone about this as well. He does not believe in lapping bars for the most part.
Filing is even going to take more off and make them more uneven. |
|
Lifetime warranty and excellent customer service don't mean a thing when your gun fails during a zombie attack.
"A Liberal is a person who will give away everything they don't own." |
|
saitotiktmdog
Optics Apprentice Joined: June/08/2010 Location: IN Status: Offline Points: 256 |
Post Options
Thanks(0)
|
Thats why filed down the flats between halves to adjust accordingly. Anyways I am if anything just performing kind of an experiement here and will let you know how it turns out. If it fails miserably than so be it. The rings ar good and solid just poorly toleranced on the diamter between the two halves. In my opinion the best way to go would actually be to use slightly oversized rings and get rubber or polyurethane reducers that reduce down to just less than scope diameter so there is some squish in the rubber or urethane so that you get 100 percent contanct due to the doformation of the rubber or urethane. If I happen to open the rings up too far I will see about using something like electrical tape as a shim between the scope and the rings. I am not saying that how you do things is wrong. I am just trying something to see what kind of results I can get. I will see what happens and report.
|
|
supertool73
Optics God Superstool Joined: January/03/2008 Status: Offline Points: 11814 |
Post Options
Thanks(0)
|
You should check out Burris Signature Zee rings. They have the bushings just like you are talking about. They are very popular rings.
|
|
Lifetime warranty and excellent customer service don't mean a thing when your gun fails during a zombie attack.
"A Liberal is a person who will give away everything they don't own." |
|
saitotiktmdog
Optics Apprentice Joined: June/08/2010 Location: IN Status: Offline Points: 256 |
Post Options
Thanks(0)
|
This would also automatically correct mild misalignment issues.
|
|
biggreen747
Optics Journeyman Joined: October/16/2009 Location: Colorado Status: Offline Points: 470 |
Post Options
Thanks(0)
|
I use Burris Signature rings on almost everything... Saves alot of hassle and I have never had scope problems due to mounting issues. I dont have ring marks when removing a scope either. I am in total agreement that most receivers are way out of wack which is what causes the problems in the first place.
|
|
We measure it with a micrometer, mark it with a crayon, and cut it with a chainsaw.
|
|
8shots
Optics Jedi Knight Lord Of The Flies Joined: March/14/2007 Location: South Africa Status: Offline Points: 6253 |
Post Options
Thanks(0)
|
The cheapest option is to let a machine shop turn you a 30mm bar. Probably $5. Wrap the sandpaper of correct grit around that and use it to lap rings. Make sure bar is long enough to span both rings. Again, just remove high spots. Then sand enough again to align rings without reducing 30mm diameter. If you are using split rings, then you can sand the contact points between the two halves to give enough space (2 thou or so), for tight clamping.
|
|
stickbow46
Optics Master Extraordinaire Joined: January/07/2009 Location: Benton, Pa Status: Offline Points: 4678 |
Post Options
Thanks(0)
|
Unfortunately lapping is one of those topics like the proper way to break in a barrel.Again it comes down to lap or not to lap.I beleive in the old fashion way of coating a new barrel:Fire 1 round/clean[10x]Fire 2 rd sets clean & let the barrel cool etc.I don't beleive in lapping the barrel,go figure.Thanks for all the info guys.
|
|
Pearls of Wisdom are Heard not Spoken
|
|
saitotiktmdog
Optics Apprentice Joined: June/08/2010 Location: IN Status: Offline Points: 256 |
Post Options
Thanks(0)
|
I actually got some really good results. Scopelines up well, drops right in tightly to the lower halves when mounted to a scope rail. The top halves fit over tightly but not too tightly. No gaps etc. Clamped down firm with no issues. Anyway as far as I am concerned the experiment was a success. Lots of great info though. ONe of these days when I am rich and famous I may get the tools of the trade but for as little as I move scopes around in this situation I didn't see the harm. Now when I get my new vortex and new rings, if things dont jive I will get it done right. I got talley lightweight aluminum mounts in 30mm. The base is built in to the ring so I do not need a separate rail. Should be a good setup.
|
|
stickbow46
Optics Master Extraordinaire Joined: January/07/2009 Location: Benton, Pa Status: Offline Points: 4678 |
Post Options
Thanks(0)
|
Glad to hear all went well,nothing ventured ,nothing gained.I use Talley's all the time,very few high spots.Don't forget to use a little long lasting oil to help prevent rusting on the scope.
|
|
Pearls of Wisdom are Heard not Spoken
|
|
TheDuke
Optics GrassHopper Joined: August/19/2010 Location: FLA Status: Offline Points: 22 |
Post Options
Thanks(0)
|
I have used all types of rings, but have come to the integral Talley's you mention. Very simple, rock solid and less to go wrong. I switched from Leupold dual dove tails. I would say to LAP every Talley ring though as they will cause marks. 1 of the 2 issues I have with them 1) Marks due to roughness and 2) Finish is not nearly as good as the leupolds (maybe part of the reason for the roughness).
|
|
Post Reply | Page 12> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |