Visit the SWFA.com site to check out our current specials. |
AR-15 Trigger Job |
Post Reply | Page 12> |
Author | ||
SVT_Tactical
MODERATOR Chief Sackscratch Joined: December/17/2009 Location: NorthCackalacky Status: Offline Points: 31233 |
Post Options
Thanks(0)
Posted: December/29/2009 at 09:11 |
|
advise deleted Edited by SVT_Tactical - December/31/2009 at 07:56 |
||
supertool73
Optics God Superstool Joined: January/03/2008 Status: Offline Points: 11814 |
Post Options
Thanks(0)
|
|
Did you reharden the metal? If you didn't they will wear out in very few rounds and your gun could have the potential to start shooting bursts.
Sears and hammers and hardened from the factory so they will not wear out very fast. Just the slightest polishing and grinding will wear that very thin layer or hardener right off the trigger. |
||
Lifetime warranty and excellent customer service don't mean a thing when your gun fails during a zombie attack.
"A Liberal is a person who will give away everything they don't own." |
||
SVT_Tactical
MODERATOR Chief Sackscratch Joined: December/17/2009 Location: NorthCackalacky Status: Offline Points: 31233 |
Post Options
Thanks(0)
|
|
I thought of that too but looked at the material and even called a couple manufacturing/distributor companies for USGI triggers. They all stated there was no hardening process done to the parts where the sears touch. I will let you know in the long run if anything comes up but on a few ar forums some guys have ran this set up for years with no problems.
Edited by SVT_Tactical - December/29/2009 at 10:11 |
||
338LAPUASLAP
Optics Master Scope Swapper Joined: October/17/2009 Status: Offline Points: 2596 |
Post Options
Thanks(0)
|
|
GEISSELE TRIGGERS ARE THE BEST AND WELL WORTH THE EXTRA MONEY NOTHING COMPARES TO THEM...
for the very few $$$ you will have a perfect trigger.
|
||
No one
|
||
RifleDude
MODERATOR EVIL OPPRESSOR Joined: October/13/2006 Location: Texas Status: Offline Points: 16337 |
Post Options
Thanks(0)
|
|
Whoever told you that doesn't know what he/she is talking about. All sear surfaces HAVE to be heat treated / case hardened / through hardened for longevity and safety. If the trigger parts were through hardened, you don't have a problem. If they were case hardened, you could have a problem if you ground through the case. If you polished only, chances are you don't have a problem. |
||
Ted
Money can't buy happiness... but it's much more comfortable to cry in a Porsche than on a bicycle. |
||
SVT_Tactical
MODERATOR Chief Sackscratch Joined: December/17/2009 Location: NorthCackalacky Status: Offline Points: 31233 |
Post Options
Thanks(0)
|
|
All i did was polish the above mentioned youtube video does have the guy using a stone but i wasn't looking to remove material only polish it. I have used the Geissel triggers, and your right, but for money I like my $5 investment and spent the rest of my coin on other stuff. lol |
||
cheaptrick
MODERATOR Joined: September/27/2004 Location: South Carolina Status: Offline Points: 20844 |
Post Options
Thanks(0)
|
|
Thanks for the links!
My AR GI single stage trigger is rougher than a cob and would benefit from some type of makeover, for sure.
|
||
If at first you don't secede...try..try again.
|
||
tahqua
MODERATOR Have You Driven A Ford Lately? Joined: March/27/2006 Location: Michigan, USA Status: Online Points: 9044 |
Post Options
Thanks(0)
|
|
I agree with part one and two. You would have a very hard time getting through the hardened layer using rouge and a felt wheel. If you ground with an abrasive wheel before polishing you could be in trouble. |
||
okc4956
Optics Apprentice Joined: October/13/2009 Location: Oklahoma City Status: Offline Points: 135 |
Post Options
Thanks(0)
|
|
Let us know if you run into any problems. I've got a couple I'd like to work on too. Wonder if this procedure works on an AR10?
|
||
"Democracy is two wolves and a lamb voting on what to have for lunch. Liberty is a well armed lamb contesting the outcome of the vote." Benjamin Franklin
|
||
BillyWayne
Optics Journeyman Joined: February/27/2009 Location: New Hampster Status: Offline Points: 408 |
Post Options
Thanks(0)
|
|
Hey, thanks for the info. My ar trigger is gritty. I have done trigger jobs on pistols, revolvers and rifles. This is going to be on my to do list.
|
||
John 11:35
The're taking the hobbits to Isengard!! |
||
SVT_Tactical
MODERATOR Chief Sackscratch Joined: December/17/2009 Location: NorthCackalacky Status: Offline Points: 31233 |
Post Options
Thanks(0)
|
|
It takes about 20 minutes and your results will be worth it!
And i do think the AR10 will fall under the same thing. Edited by SVT_Tactical - December/30/2009 at 08:15 |
||
Dale Clifford
Optics Jedi Knight Joined: July/04/2004 Location: United States Status: Offline Points: 5087 |
Post Options
Thanks(0)
|
|
doing trigger jobs on ars has been around sense Vietnam. most of the triggers and parts from ar's are investment castings, not good tool steel which is cut to dimension than heat treated for hardness. this means that steels using low dimensional change are chosen for the parts , to cut down on fitting labor. Ars have large dimensions in both the pins, and holes and the actual contact parts involved. In some cases I've seen sear and hammer surfaces with less than 20% contact. sometimes removing material and trying to get a higher percentage contact works. Biggest problem with the ar trigger group (besides pins and holes dimensions) is the basic design. The single lever design at the base of the hammer puts too much pressure on the contacting surfaces. also using the primary sear as part of the trigger is not a good idea for a good trigger group. In contrast the M1a trigger group uses the hammer lever further up, and reduces the release pressure considerably, and the reason why a good m1a can have an outstanding trigger pull. Most after market triggers are designed to correct this geometry mistake, and do so very well. Anything on youtube should be considered for entertainment purposes only.
|
||
SVT_Tactical
MODERATOR Chief Sackscratch Joined: December/17/2009 Location: NorthCackalacky Status: Offline Points: 31233 |
Post Options
Thanks(0)
|
|
I worked as instructional for me. Heck I build my first lower by watching the clips that midway put on YouTube. It can be more than entertainment.
|
||
pyro6999
Optics Retard OT TITAN Joined: December/22/2006 Location: North Dakota Status: Offline Points: 22034 |
Post Options
Thanks(0)
|
|
thats one thing if its from midway.
|
||
They call me "Boots"
375H&H Mag: Yeah, it kills stuff "extra dead" 343 we will never forget God Bless Chris Ledoux "good ride cowboy" |
||
SVT_Tactical
MODERATOR Chief Sackscratch Joined: December/17/2009 Location: NorthCackalacky Status: Offline Points: 31233 |
Post Options
Thanks(0)
|
|
Maybe I am interpreting this wrong....... Yes if it is from Joe Blow with his camera in his shop maybe take some warning not to take it as qualified, However the fact that so many sites are referencing the website and youtube videos to expand on what the website is talking about I figure its educational enough. I agree that not all on youtube is informational and should be used but not everything thats on there is entertainment. The number of people that are trying this technique is growing daily. Worst case senerio is for someone to try it, no like it, buy replacement springs ($5) and new trigger ($12) and be back at the start. at square one. I challenge anyone to try this and not think that this is a 100% inprovement from the stock USGI issue trigger pull.
|
||
supertool73
Optics God Superstool Joined: January/03/2008 Status: Offline Points: 11814 |
Post Options
Thanks(0)
|
|
I tried one similar to that which I found off a internet site and it
did not take long til my trigger started to not catch. Got a few
double taps. At first I could not figure out what was wrong, then it
dawned on me it must have been my do it yourself trigger job. I took
to much of the surface off and got through the hardener and just kind
of rounded my parts off a little. It only took 300 to 400 rounds to
cause it. But it was fun having it burst on the range.
It was most likely me just not doing it right, but it made me pretty nervous about doing it again. I replaced it with a Timney and it is much better than my trigger job anyway. Course it cost me $200 Brownells sell surface hardener that you can apply with a torch to harden it back up. Might be worth doing. A couple guys I know have used it on AR parts and said it works great. |
||
Lifetime warranty and excellent customer service don't mean a thing when your gun fails during a zombie attack.
"A Liberal is a person who will give away everything they don't own." |
||
SVT_Tactical
MODERATOR Chief Sackscratch Joined: December/17/2009 Location: NorthCackalacky Status: Offline Points: 31233 |
Post Options
Thanks(0)
|
|
I think the biggest warning from all this is not to remove material only polish the surfaces on the sear. I do not recommend changing specs only removing the machining marks by doing a good polish.
|
||
Dale Clifford
Optics Jedi Knight Joined: July/04/2004 Location: United States Status: Offline Points: 5087 |
Post Options
Thanks(0)
|
|
there is nothing new here, its been done since vietnam, its just you kids are finding out about it. even if you do just polish, the chances the hammer sear "chips" and goes auto is higher, basic trigger groups in most ars are basic sh*t, plain and simple. cleaning up the angles and contacts surfaces is the problem, not just a simple polish, this is best done by drop in "hanger" groups where the relation of the sears is kept constant by a box, and the entire group is allowed to float in the lower via the pin assembly.
note that bursts and doubles are caused by the hammer following the bolt carrier down and the bolt does not have time to lock up as in a true select fire arrangement, this is asking for a case head failure. While there are open bolt autos out there (have an orginal uzi) these were never orginally designed to be closed bolt as ars.
|
||
RONK
Optics Master Extraordinaire Joined: April/05/2007 Location: United States Status: Offline Points: 3199 |
Post Options
Thanks(0)
|
|
I'll throw my opinion in here if anybody cares to hear it.
I like to see guys take a serious interest in learning more about their guns, by tweaking them here and there for better performance, accuracy, etc. That's how (most) of the master gunsmiths and custom gunmakers in the world today got started, and that's how they learned, whether we like to admit it or not. (And plenty of them ruined guns along the way, too.)
That said, most triggers are almost always in a gray area in that regard, and in my opinion, auto and semi-auto triggers are in a red zone. Don't go there unless you have a true professional gunsmith looking over your shoulder. It doesn't take a great deal of imagination to envision what could happen when a good trigger goes bad. And re-worked Mil-spec AR15 triggers usually go bad fairly quickly, (usually within a couple hundred rounds, depending on how deep the case-hardening is. It is usually VERY thin!)
A semi-auto going full auto on you in the wrong place and time can literally get you thrown into prison in this day and age. It happened to a guy here in Wisconsin recently.
I don't know the full story, but his (AR?) malfunctioned and fired a burst at the range. A couple cops saw it happen, and the last I heard, he was looking at 5-10 (?) in a penitentiary. I think he is serving time now, but am not current on the story.
Want a good trigger on your AR15?
Buy a Jewell, Timney, Giesselle, or any of several others.
Seriously.
(Dale is a pretty blunt fellow sometimes, but he is dead right on this one, in every respect he mentioned.)
BTW, I'm not harpin' on ya, SVT. I know your thread is well-intentioned and I might easily have posted a similar thread in past years, before age and experience had jaded me so...
Edited for spelling. Edited by RONK - December/30/2009 at 19:22 |
||
Sgt. D
Optics Master Extraordinaire Joined: February/20/2008 Location: North Carolina Status: Offline Points: 4525 |
Post Options
Thanks(0)
|
|
Thanks Dale and Ronk. Your experience can help save alot of heart ache "if heeded". I don't hesitate to polish or tweak something if I can't find any info on the pros & cons. But like you said, I run the risk of having to start over or replace parts sometimes. My advantage is years of experience making tools and parts when needed. Or know I can order what I need if necessary. I also appreciate you statment about being willing to make the effort for improvment. It helps one to better understand function and purpose. Then before you know it someone has come up with an improvment that we all can benefit from.
|
||
Take care of Soldiers, Show em how its done and do it with em, Run to the Fight & and hold your ground! I die my men go home! If you're a NCO and this ain't you. GET OUT! GOD BLESS AMERICA!
|
||
Post Reply | Page 12> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |